Origami Folded Fabric Ornaments
Kevin MacLeod made a great video showing how to make origami folded fabric ornaments. Thanks to his video I’ve been having a blast making Christmas ornaments! Take a look and then come right back for my tips below.
1. Pre-wash your fabric. I know, I can hear the moaning already. If you pre-wash (and iron) you don’t have to pin anything. Because pre-washed cottons slide less than un-washed cottons.
2. Pick two, freshly pressed, coordinating Christmas fabrics and place them right sides together on a flat surface. If the selvage edges are still intact, make sure they are lined up. If they’ve gone missing, figure out where the straight of grain is and line up both fabrics so that the straight of grain is running the same way in both fabrics.
3. Flip your lid (or your mixing bowl) rim side down and trace around with a super very thin permanent pen. (You read that correctly. Permanent.) Permanent pen lines will be cut off and what little might remain won’t bleed if the pen is permanent. Then trace some more circles because you’ll want to make lots of ornaments. The lines you are tracing CAN TOUCH. In fact, they probably should, so you can save fabric. (You’ll see why shortly.)
4. (If you didn’t pre-wash/dry you get to pin now. All over. Lots of pins. Nasty, pointy pins. Be careful.) Dial down your stitch length a notch, and sew 1/8″ from the marked line on the inside of the circle. A shorter stitch length and narrower seam allowance make for a smoother, rounder edge. When you turn the disk right sides out, the seam allowance will have shorter and less noticeable pleats. (The marked line is your cutting line.) Go ALL THE WAY AROUND leaving no opening. OH MY! Is she for real?! YES! Do you want to tuck in a 1/8″ seam allowance and blind stitch it shut? Me neither.
5. Do the folding thing in the video to find dead center. (I know, we’re still inside out.) Mark dead center on both fabric with the dreaded permanent ink pen. I hope it oozes through the fabric because you’ll be looking for the marks on the right side of the fabric.
6. Make a 1″ slit in ONE fabric 1″ away from the marked dead center, like this. The fabric you slit will NOT be the one that slips over the ornament corners. The slit will be on the back of the ornament cleverly concealed by something I have not not yet revealed.
7. Turn disk right-side out. Push out seam allowance with chopstick. Lick your fingers and wiggle the two fabrics back and forth at the seam to draw out any hidden creases. You can also pick them out with a pin.
8. Fold disk again, as in the video, to make hard creases that evenly divide it into quarters. (Pins take over for creases in humid weather or if you’re dragging this project around for a while.) Sew a button to the non-slit side, dead center. Shank buttons are the best. If you don’t have a button with a shank, go get one. Or make a thread shank. Sew with stiff, sturdy thread like Coats & Clark hand quilting thread. Knot off the thread after sewing on the button, but LEAVE A VERY LONG TAIL. (Can you see how old my thread is? $.91 WOW! And did you notice I forgot to stitch decoratively about 1/8″ from the edge? I think I’m OK with that.)
9. With the thread from sewing on the button exiting the top fabric at the button shank, pick a pin, any pin (or creased side). Spear it just like Kevin did in the video and pull it all the way to the button shank, taut. Take a stitch in the fabric right next to the thread shank to anchor it.
10. Moving clockwise or counter-clockwise (whichever is most comfortable) take a tiny stitch to anchor the thread on the next side of the button very, very near the shank and pierce the next crease. Bring it to the button. Take a stitch as before to anchor it.
11. Repeat with the last two creases, take thread to the back and knot off. You can make as big a mess as you want with the knot on the back. The knot and the slit will be covered.
12. Press the sides, then fold over and nail the point with your iron. Steam is good.
13. Make the final flips like Kevin showed. Press.
14. Flip the ornament over and cut a square of Sticky Template Plastic (STP) that is it 1/4″ smaller than the ornament. The STP insert will be covered in fabric and inserted down in Step #17.
15. Peel off the release paper, stick it on the wrong side of a piece of matching fabric and, with a rotary cutter, trim the fabric a hefty 1/4″ beyond the edge of the plastic.
16. Cut strips of STP 1/2″ wide by 1/2″ LESS than the width of the square above. In a two-step process, stick an STP strip to the right side of the fabric, and then wrap the fabric to the wrong side and press the STP to secure it. Don’t worry about the mess in the corners.
17. Center the insert on the back of the ornament and then finish as Kevin suggested with a hanging cord or thread. The fabric-covered STP straightens up the ornament nicely, gives it a little heft, and lets you dress up the “back end.”
18. Insert something to hang the ornament with, like Kevin showed in the video. I settled on 11″ of red pearl cotton #5 and used a big fat needle.
19. Now what? Use a gel pen or permanent pen to sign and date your ornament, or write a little message to the recipient. Maybe before you slapped the STP on the fabric you could have embroidered something? Next time. Here’s another idea: tape a length of ribbon to the non-fabric side of the STP and tie a gift card to the back of the ornament. See how nicely it tucks into the corners for extra security? Fuse or sew a QR code to the STP insert. Upload a video, photo, or favorite recipe to be accessed with the QR reader on your smart phone.
The original post for this awesome ornament came from a woman in New Zealand. Click here to read Katrina’s Tutorials blog.
Get Sticky Template Plastic here.
Get fusible or sew-on QR codes (with subscription to cloud storage included) here.
Entry filed under: Quilting.